Skip to main content

Free mini-split quotes

Call (347) 443-8854
Staten Island AirMini-Splits · Heating · Cooling

Mini-Split Installation in Staten Island

A mini-split cools and heats your home without ducts. No wall demolition. No dripping window units. We design and install Mitsubishi systems across Staten Island — and we handle the rebate paperwork for you.

Mini-splits (also called ductless systems) are the best fix for the rooms Staten Island homes struggle with: finished attics, garage conversions, additions, and older houses that never had ductwork. One small outdoor unit connects to quiet indoor heads. Each head has its own thermostat.

They heat, too. The cold-climate Mitsubishi units we install put out full heat at 5°F. Staten Island's coldest design days are around 15°F, so a properly sized system carries the whole winter. Many of our customers heat and cool their homes with nothing else.

Every install starts with a load calculation — never a guess from the driveway. You get a written quote with model numbers, priced net of current Con Edison rebates. We file the rebate and warranty paperwork ourselves.

Looking for this service near you?

Dedicated local pages with pricing, response times, and neighborhood-specific advice:

A mini-split is a good fit if…

  • You have a finished attic, sunroom, or garage that no duct has ever reached
  • You want AC in an older home without cutting open plaster walls
  • You're tired of window units — mini-splits cool at 2–3x the efficiency
  • You heat with oil, propane, or electric baseboard and the bills hurt
  • Your top floor roasts in July no matter what the thermostat says
  • You want one system that handles both heating and cooling

Ductless and heat pump work we do

Single-zone mini-split installs

One outdoor unit, one indoor head — the fix for one problem room. Most single-zone installs are done in a day, with the line set routed so it doesn't scar your siding.

Multi-zone whole-home systems

One outdoor unit can feed up to eight indoor heads, each with its own thermostat. This is how we cool and heat whole pre-war homes without adding a single duct.

Ducted cold-climate heat pumps

If your home already has good ductwork, a ducted heat pump from Carrier, Trane, Lennox, Rheem, or Goodman can reuse it. It replaces your AC and adds heating in the same box.

Rebates, permits & paperwork

We confirm current NYS Clean Heat (Con Edison) rebate amounts at quote time, price the job net of them, file NYC DOB permits, and register your warranty so it's actually valid.

Mini-split service & repair

We repair all major ductless brands — error codes, sensors, boards, refrigerant leaks — even if someone else installed the system.

Why mini-splits fit Staten Island homes so well

So much of this borough is semi-attached homes, finished attics, and pre-war houses with radiators and no ducts. Mini-splits solve all three without construction. That's why they're the system we install most.

Near the shore — South Beach, Midland Beach, Tottenville — salt air eats outdoor equipment. We use coastal-coated coils and stainless hardware there as standard. In flood-mapped blocks, we mount outdoor units on brackets or raised pads. This area learned that lesson in 2012.

Recent mini-split installs, scope by scope

The neighborhood, the home, the configuration, and what it solved — told the way we'd tell a neighbor.

Westerleigh, Staten Island · 1930s detached colonial

4-zone Mitsubishi hyper-heat multi-split — one head on the open first floor, three bedroom heads upstairs; gas boiler kept as cold-snap backup

The problem: Three window units every May, radiators with no cooling at all, and a second floor that never dropped below 80°F on July nights.

What changed: Window units retired for good, each bedroom on its own thermostat, and the boiler now fires only on the coldest nights. Line sets run down the rear wall in painted line-hide — nothing visible from the street.

Midland Beach, Staten Island · flood-zone cape cod with a finished attic

Single-zone 12,000 BTU cold-climate mini-split; condenser on an elevated bracket above flood grade, coastal-coated coil and stainless hardware

The problem: A finished attic office no duct had ever reached — unusable after noon from June to September, and a block where salt air and the 2012 flood line rule the equipment choices.

What changed: The attic now holds its own temperature year-round, the condenser sits above the flood line on a wall bracket, and the coastal spec means the coil isn't on an eight-year corrosion clock.

Bay Ridge, Brooklyn · brick rowhouse

2-zone Mitsubishi multi-split for the top floor — two bedroom heads fed from a rear-yard condenser, line sets chased down the rear facade

The problem: A top floor under a flat black roof running 12–15 degrees hotter than the parlor level, in a house with plaster walls nobody wanted opened.

What changed: Both top-floor bedrooms hold their set temperature through heat waves. All penetrations came through the rear brick — no plaster was cut, and the street-facing facade is untouched.

Hudson Heights, Manhattan · pre-war co-op apartment

Single-zone ductless system with board-approved placement; condensate pumped to an approved drain line rather than dripped to the setback

The problem: Radiator heat with no cooling, a co-op board with a real alteration agreement, and a building engineer with opinions about where condensate goes.

What changed: We prepared the alteration package and insurance certificates the board required, placed the equipment per the building's rules, and the apartment got quiet cooling without a window unit blocking the fire escape.

Research first — our homeowner guides

Costs, rebates, and sizing, answered with real local numbers you can hold any quote against:

Mini-Split Installation: your questions

How much does a mini-split cost installed?

Single-zone systems usually run $4,500–$6,500 installed. Multi-zone and whole-home systems typically run $14,000–$25,000 before rebates, depending on size. Every quote is written, with model numbers, and priced net of current rebates.

Do mini-splits really heat through a Staten Island winter?

Yes. Cold-climate models hold full rated heat at 5°F, and our design temperature is about 15°F. We size in extra margin, and many customers here heat all winter on the mini-split alone.

Can I keep my boiler and still add a mini-split?

Yes — that's a popular setup in older North Shore homes. The mini-split handles cooling and mild-weather heating. The boiler takes over on the coldest nights. Your radiators stay right where they are.

Are the rebates real?

Real, but they change. NYS Clean Heat (Con Edison) applies on Staten Island, and NJ utilities run their own programs. We confirm current amounts when we quote and show your price net of rebates.

How long does an install take?

Most single-zone installs are one day. Multi-zone whole-home systems usually take two to three days, depending on line-set routing. We tell you the plan before we start.

Will you service a mini-split someone else installed?

Yes. We're factory-trained on Mitsubishi and repair all major ductless brands. If the original install has problems — bad drainage or uninsulated line sets are common — we document and fix those too.

Book Mini-Split Installation today

Written price before any work starts. Same-day slots most days.

Text us a photo of the room or your current unit and we'll reply with next steps during business hours.